Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 52

Page: 52 / 147

OPERATION

eng

IMPORTANT: Always check the ground connections and power

leads for corrosion and tightness. If the ground leads are loose

or dirty, current will not flow.

a -

Battery lead cover

b -

Battery connection

c -

110 AMP fuse

d -

Starter solenoid

e -

Starter motor

f -

Flywheel housing

g -

Ground connections

7. Eight fuses are located at the upper rear of the engine in two

fuse holders (four fuses in each holder).

Fuse Holder ‑ C24

Fuse Holder ‑ C25

(1) ‑ 5 amp ‑ YEL/PPL to YEL CAN (1) ‑ 20 amp ‑ RED/GRN to RED/WHT

Fuel injectors

(2) ‑ 5 amp ‑ RED to RED/WHT

MPR

(2) ‑ 25 amp ‑ RED/PNK to RED/BLK

Fuel pump, Alternator

(3) ‑ 2 amp ‑ RED to RED/ORN

Diagnostics

(3) ‑ 20 amp ‑ RED/YEL to RED/GRN

Ignition coils

(4) ‑ 15 amp ‑ RED/PPL to RED

Key switch power

(4) ‑ 20 amp ‑ RED/GRN to RED/BLU

Fuel pump relay, IAC, Trim limit relay,

PCM

14325

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands