Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 103

Page: 103 / 147

MAINTENANCE

eng

NOTE: Some damaged propellers can be repaired. Contact

your authorized Mercury MerCruiser dealer.

a -

Rear propeller nut

b -

Rear propeller

c -

Rear propeller thrust hub

d -

Front propeller nut

e -

Front propeller

f -

Front propeller thrust hub

g -

Propeller shaft anode screw

h -

Flat washer

i -

Star washer

j -

Propeller shaft anode

Installation

NOTICE

Operating the engine with a loose propeller can damage the

propeller, the drive, or drive components. Always tighten the

propeller nut or nuts to specification and check for tightness

periodically and at the required maintenance interval.

5304

g h

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands