Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 57

Page: 57 / 147

OPERATION

eng

3. See

Power Trim

section for detailed power trim operating

procedures.

Power Trim

Power Trim allows the operator to adjust the drive angle while

underway to provide the ideal boat angle for varying load and

water conditions.
IMPORTANT: Each boat manufacturer has the option as to how

the power trim will function on their particular boat. The boat

owner/operator must be aware of how the power trim functions

before operating the boat.
In most cases, best overall performance is obtained with the

drive unit adjusted so the boat bottom will run at a 3° to 5° angle

to the water.

a -

Boat bottom at 3° to 5° angle with water

Trimming Drive Unit Up/Out Can:

• Generally increase top speed.
• Increase clearance over submerged objects or a shallow

bottom.

• Cause the boat to accelerate and plane off slower.

7418

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands