Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 108

Page: 108 / 147

MAINTENANCE

eng

STERNDRIVE WATER PICKUPS

There are three types of water pickups available on Mercury

MerCruiser sterndrives: low water, dual water and side pickups.

Dual water pickups require the flushing attachment (91‑44357Q

2) and the flush seal kit (91‑881150K 1). The High‑Performance

low‑water pickup drive requires the flushing attachment

(91‑849996T 1) while the SportMaster low water pickup drive

requires flushing attachment (91‑843122A01). Side pickups

require the flushing attachment (91‑44357Q 2).

5752

Dual water pickup

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands