manualshive.com logo in svg

Factory Five Racing Hot Rod Coyote, Installation Instructions Manual

The Factory Five Racing Hot Rod Coyote is a powerful and sleek hot rod kit that will bring your dream car to life. Ensure seamless assembly with our comprehensive Installation Instructions Manual, available for free download at manualshive.com. Get behind the wheel and experience the thrill of this iconic vehicle.

Share
Download
background image

 

Factory Five Racing, Inc. 

DO NOT DUPLICATE CONFIDENTIAL INFORMATION AND PROTECTED UNDER U.S. COPYRIGHT LAWS 

 2012 FACTORY FIVE RACING, INC.

 

Company/instructions

 

Part Number: 33871 

 

Revision: D 

 

Effective Date: 6/4/12 

 

 By:  J. INGERSLEV 

Document Type (indicate): 
 

 

 

 Bill of Material      

 

 Drawing (may be attached)  

 Specification 

 

 

 

 Assembly Instructions    

 

 Operating Procedure 

 

 Other 

Hot Rod Coyote Engine 

Installation Instructions  

 

Parts needed ..............................................................................................................................................................................2

 

Ford Racing Parts ..................................................................................................................................................................2

 

Ford Motor Co. Parts .............................................................................................................................................................3

 

Summit Racing ......................................................................................................................................................................3

 

Fuel System .......................................................................................................................................................................3

 

Air Intake System ..............................................................................................................................................................3

 

Other vendors ........................................................................................................................................................................3

 

Autozone ...........................................................................................................................................................................3

 

Supplies.....................................................................................................................................................................................3

 

Information ...............................................................................................................................................................................4

 

Engine prep ...............................................................................................................................................................................4

 

Oil filter relocator ..................................................................................................................................................................4

 

Oil Pressure sender ................................................................................................................................................................9

 

Water Temp Sender .............................................................................................................................................................13

 

Engine Bolts ........................................................................................................................................................................17

 

Alternator Boss....................................................................................................................................................................18

 

Transmission Prep ...................................................................................................................................................................19

 

Summary of Contents for Hot Rod Coyote
























































































































Reviews:

No comments

Related manuals for Hot Rod Coyote

Briggs & Stratton Vanguard EFI 380000 Repair Manual preview
Vanguard EFI 380000
Brand: Briggs & Stratton Pages: 100
Jiecang JCA35SEW01 Quick Start Manual preview
JCA35SEW01
Brand: Jiecang Pages: 2
MOOG ANIMATICS Smart Motor SM23166MT Manual preview
Smart Motor SM23166MT
Brand: MOOG ANIMATICS Pages: 32
LAMBERT 6D10D200A User Manual preview
6D10D200A
Brand: LAMBERT Pages: 24
Westerbeke 27a Specifications preview
27a
Brand: Westerbeke Pages: 2
Westerbeke 10.0 KW-60Hz SBEG Service Manual preview
10.0 KW-60Hz SBEG
Brand: Westerbeke Pages: 104
Forest-Master MLR52 Manual preview
MLR52
Brand: Forest-Master Pages: 16
Yanmar 8LV320 Operation Manual preview
8LV320
Brand: Yanmar Pages: 84
Honda GXV270 Owner'S Manual preview
GXV270
Brand: Honda Pages: 31
DANA 4360-61 Parts List preview
4360-61
Brand: DANA Pages: 3
STEYR MOTORS MO114K33 Operation, Maintenance And Warranty Manual preview
MO114K33
Brand: STEYR MOTORS Pages: 134
STEYR MOTORS Marine Engine 2012 Series Service Manual preview
Marine Engine 2012 Series
Brand: STEYR MOTORS Pages: 274
KTM 250 1998 Repair Manual preview
250 1998
Brand: KTM Pages: 59
Mitsubishi FD Instruction Manual preview
FD
Brand: Mitsubishi Pages: 20
Hägglunds Compact CBP Series Installation And Maintenance Manual preview
Compact CBP Series
Brand: Hägglunds Pages: 32
Newport Vessels L-62 User Manual preview
L-62
Brand: Newport Vessels Pages: 18
GAPOSA XQ40EX Instructions Manual preview
XQ40EX
Brand: GAPOSA Pages: 8
Yamaha 9.9C Service Manual preview
9.9C
Brand: Yamaha Pages: 135

Brands by name

Popular brands

Load more brands