Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 44

Page: 44 / 147

SPECIFICATIONS

eng

Engine Operating Limitations

Maximum wide open throttle (W.O.T.) RPM

4800 ‑ 5300 RPM

Rev limit

5400 RPM

Idle RPM in gear

700 RPM

Idle RPM out of gear

750 RPM

Maximum fuel system flow rate

163 L/hr (43 gals/hr) at 5200

RPM

Fuel pressure at Sea Level

262‑296 kPa (38‑43 psi)

Coolant thermostat initially opens at

temperature

62° C (143° F)

Coolant thermostat is at maximum open at

temperature

71° C (160° F)

Minimum water pressure supplied to the

engine at WOT

207 kPa (30 psi)

Maximum water pressure supplied to the

engine at WOT

296 kPa (43 psi)

Minimum oil pressure at idle (Hot)

138 kPa (20 psi)

Minimum oil pressure at WOT (Hot)

331 kPa (48 psi)

Maximum oil temperature

121° C (250° F)

a -

Front of engine and boat

b -

Firing order 1‑8‑4‑3‑6‑5‑7‑2

6985

1. Engines are equipped with an ignition system that has a built‑in 5400 RPM rev limiter.

Engine is performing normally if it will not exceed this RPM.

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands