Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 24

Page: 24 / 147

GENERAL INFORMATION

eng

Before Operating Your Boat

Read this manual carefully. Safety and operating information that

is practiced along with using good common sense can help

prevent personal injury and product damage. If you have any

questions, contact your dealer.
This manual as well as safety labels posted on the engine

package use safety alerts to draw your attention to special safety

instructions that must be followed.

WARNING

Indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

Indicates a hazardous situation which, if not avoided, could

result in minor or moderate injury.

IMPORTANT: Indicates information or instructions that are

necessary for proper operation and/or maintenance.

NOTE: Indicates information that helps in the understanding of a

step or action.

Boat Horsepower Capacity

WARNING

Exceeding the boat's maximum horsepower rating can cause

serious injury or death. Overpowering the boat can affect boat

control and flotation characteristics or break the transom. Do

not install an engine that exceeds the boat's maximum power

rating.

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands