Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 46

Page: 46 / 147

OPERATION

eng

Instrumentation

Mercury Racing requires that the following critical engine
functions be monitored:

• Oil pressure
• Engine RPM
• Oil temperature
• Water temperature
• System voltage
• Guardian fault messages

The use of SmartCraft instrumentation will display all of the
above critical engine functions as well as others not listed.
SmartCraft instrumentation will also display information
about power train sensor faults and Guardian activation.

Warning System

The engine's warning system includes an audible alert consisting

of a horn located in the helm harness, and the Engine Guardian

system. Do not attempt to alter or disable the warning system in

any way.

NOTICE

A continuous horn indicates a critical fault. Operating the

engine during a critical fault can damage components. If the

warning horn emits a continuous beep, do not operate the

engine unless avoiding a hazardous situation.

ENGINE GUARDIAN SYSTEM

The Engine Guardian system monitors sensors on the engine for

any early indications of problems. If a sensor indicates a fault,

the system responds to the problem by emitting a continuous or

intermittent horn and, depending on the type of fault, may reduce

engine power to provide engine protection. If the boat is

equipped with System View, a message will be given on the

display screen in conjunction with the horn. Refer to the System

View manual for details. When the key switch is turned "ON", the

warning system's horn beeps once to verify horn operation.

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands