Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 30

Page: 30 / 147

GENERAL INFORMATION

eng

GOOD VENTILATION

Ventilate passenger area, open side curtains, or forward hatches

to remove fumes.

5448

Wave and Wake Jumping

Operating recreational boats over waves and wake is a natural

part of boating. However, when this activity is done with sufficient

speed to force the boat hull partially or completely out of the

water, certain hazards arise, particularly when the boat enters

the water.

5450

The primary concern is the boat changing direction while in the

midst of the jump. In such case, the landing may cause the boat

to veer violently in a new direction. Such a sharp change in

direction can cause occupants to be thrown out of their seats, or

out of the boat.

WARNING

Wave or wake jumping can cause serious injury or death from

occupants being thrown within or out of the boat. Avoid wave

or wake jumping whenever possible.

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands