Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 94

Page: 94 / 147

MAINTENANCE

eng

8. Fill drive unit, through the oil fill/drain hole until an air‑free

stream of lubricant flows from the oil vent hole.

a -

Oil fill/drain screw

b -

Sealing washer

Tube

Ref No.

Description

Where Used

Part No.

SAE 85W90

Mercury

Racing Gear

Oil

Drive unit

8M0078015

9. Install the oil vent screw and sealing washer.
10.Continue to pump gear lube into the gear lube monitor

circuit until oil appears in the monitor.

11.Fill the monitor to the top line of the "OPERATING RANGE".
12.Lubricate O‑ring on the neck. Install the filler cap, being

careful to not overtighten.

13.Remove the pump from the oil/ fill/drain hole.
14.Quickly install the sealing washer and the oil fill/drain screw.

Tighten securely.

15.Re‑check the oil level after first use.

IMPORTANT: Oil level in the gear lube monitor will rise and fall

during drive operation. Always check the oil level when the drive

is cool and the engine is shut down.

18912

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands