Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 140

Page: 140 / 147

TROUBLESHOOTING

130

eng

Battery Will Not Come Up On Charge

Possible Cause

Remedy

Excessive current draw from

battery.

Turn off non‑essential accessories.

Loose or dirty electrical

connections or damaged wiring.

Check all associated electrical

connections and wires (especially

battery cables). Clean and tighten faulty

connections. Repair or replace damaged

wiring.

Alternator drive belt loose or in

poor condition.

Replace and/or adjust.

Defective battery.

Test battery.

Power Trim Does Not Operate (Motor Doesn't

Run)

Possible Cause

Remedy

Open fuse.

Replace fuse.

Loose or dirty electrical

connections or damaged

wiring.

Check all associated electrical connections

and wires (especially battery cables). Clean

and tighten faulty connections. Repair or

replace damaged wiring.

Power Trim Does Not Operate (Motor Runs But

Drive Unit Does Not Move)

Possible Cause

Remedy

Trim pump oil level low.

Fill pump with oil.

Drive binding in gimbal ring.

Check for obstruction.

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands