Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 62

Page: 62 / 147

OPERATION

eng

NOTE: The word trim is usually considered the first 20° up/out

movement from vertical position.

1 -

Trailering and trimming up/out position

‑

Press (top)

up/out portion of switch until drive unit reaches desired

trim/trailering position.

2 -

Trim drive unit in/down position

‑

Press (bottom) in/

down portion of switch until drive unit reaches desired

trim position.

Starting, Shifting and Stopping

WARNING

Explosive fumes contained in the engine compartment can

cause serious injury or death from fire or explosion. Before

starting the engine, operate the bilge blower or vent the engine

compartment for at least five minutes.

NEW ENGINES OR ENGINES COMING OUT OF STORAGE

See

Power Package Recommissioning.

7868

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands