Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 116

Page: 116 / 147

MAINTENANCE

106

eng

1. Remove the water separating fuel filter and sealing ring from

mounting bracket and discard.

a -

Water separating fuel filter

b -

Sealing ring

c -

Mounting bracket

2. Coat the sealing ring on new filter with motor oil.

IMPORTANT: Do not use a filter wrench to tighten the filter.

3. Thread the filter onto the bracket and tighten securely by

hand.

4. Start and run engine. If the engine stops or will not start, it

may be necessary to prime the fuel system (see

Priming the

Fuel System Prior to Starting

in the

Cold Weather or

Extended Storage

section of this manual).

5. Check the filter connection for fuel leaks. If leaks exist,

recheck the filter installation.

6. If leaks continue, stop the engine immediately and contact

your authorized Mercury MerCruiser dealer.

6152

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands