Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 89

Page: 89 / 147

MAINTENANCE

eng

IMPORTANT: If any water drained from the oil fill/drain hole, or

if oil appears milky, drive unit is leaking and should be checked

immediately by your authorized Mercury MerCruiser dealer.

a -

Sealing washer

b -

Oil vent screw

3. Adjust the drive unit so the propeller shaft is level.
4. Fill the drive unit through the oil fill/drain hole until an air‑free

stream of lubricant flows from the oil vent hole.

a -

Oil fill/drain screw

7987

7988

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands