Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 104

Page: 104 / 147

MAINTENANCE

eng

IMPORTANT: Mercury Marine designed the Bravo III XR

propellers as matched sets. Do not operate the drive without a

front and rear XR propeller of the same pitch. Do not mix Bravo

III XR propellers with non‑XR propellers or use a non‑XR

propeller on a Bravo XR drive. Doing so voids the product

warranty.

a -

Rear propeller nut

b -

Rear propeller

c -

Rear propeller thrust hub

d -

Front propeller nut

e -

Front propeller

f -

Front propeller thrust hub

g -

Propeller shaft anode screw

h -

Flat washer

i -

Star washer

j -

Propeller shaft anode

1. Slide the forward thrust hub onto the propeller shaft with the

tapered side toward the propeller hub.

2. Apply a liberal coat of one of the following lubricants to the

propeller shaft.

5304

g h

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands