Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 93

Page: 93 / 147

MAINTENANCE

eng

5. Remove the oil fill/drain screw and sealing washer and drain

the oil.

a -

Oil fill/drain screw

b -

Sealing washer

6. Remove the oil vent screw and sealing washer. Allow the oil

to drain completely.

IMPORTANT: If any water drains from the oil fill/drain hole, or if

the oil appears milky, the drive unit is leaking and should be

checked immediately by your authorized Mercury MerCruiser

dealer.

a -

Sealing washer

b -

Oil vent screw

7. Lower drive unit so propeller shaft is level.

mc79507-1

7991

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands