Mercury Racing HP525 EFI Bravo Sterndrive Series Operation, Maintenance & Warranty Manual Download Page 88

Page: 88 / 147

MAINTENANCE

eng

152

25W-50

Verado

FourStroke

Outboard Oil

Crankcase

92-858084K01

MerCruiser 4-

cycle 25W40

Engine Oil

Engine crankcase

92-858048K01

DRIVE UNIT OIL (BRAVO ONE XR MODELS)

IMPORTANT: Use only High Performance Gear Lube in the

drive unit.

1. Remove the propeller, place the drive unit in full down

position, remove the oil fill/drain screw and sealing washer,

and drain the oil.

a -

Oil fill/drain plug

2. Remove the oil vent screw and sealing washer. Allow the oil

to drain completely.

7986

Summary of Contents for HP525 EFI Bravo Sterndrive Series




















































































































































Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands

Mercury Racing HP525 EFI Bravo Sterndrive Series, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP525 EFI Bravo Sterndrive Series

Reviews:

Related manuals for HP525 EFI Bravo Sterndrive Series

Brands by name

Popular brands