background image

It is of vital importance, before attempting to 
operate your engine, to read the general 
'SAFETY INSTRUCTIONS AND WARNINGS' 
section on pages 2-5 of this booklet and to strictly 
adhere to the advice contained therein.

Also, please study the entire contents of this 
instruction manual, so as to familiarize yourself 
with the controls and other features of the 
engine.

Keep these instructions in a safe place so that 
you may readily refer to them whenever 
necessary.

It is suggested that any instructions supplied 
with the vehicle, radio control equipment, etc., 
are accessible for checking at the same time.

1

2-5

6

7-8

8

9-12

12

13

15

15-18

21

23

24-27

28-29

30

13-14

21-22

18-19

20

SAFETY INSTRUCTIONS AND 
WARNINGS ABOUT YOUR O.S. ENGINE

INTRODUCTION, BASIC ENGINE PARTS

INSTALLATION OF THE CARBURETOR

INSTALLATION OF THE ENNGINE

AIR CLEANER TYPE201

NOTES CONCERNING THE RECOIL STARTER

GLOWPLUG

TOOLS, ACCESSORIES, etc. 

CARBURETOR CONTROLS,

STARTING THE ENGINE &

RUNNING-IN('Breaking-in)

FINAL ADJUSTMENT

CARBURETOR CLEANLINESS

BEFORE STARTING THE ENGINE

GUARANTEE

PRESSURIZED FUEL SYSTEM

CARE AND MAINTENANCE

22

O.S. GENUINE PARTS & ACCESSORIES

ENGINE EXPLODED VIEW
& ENGINE PARTS LIST
 
CARBURETOR EXPLODED VIEW
& PARTS LIST

THREE VIEW DRAWING

18

IF THE ENGINE FAILS TO START 

CONTENTS

Summary of Contents for MAX-21RG Series

















Reviews: