McDATA Enterprise Operating System User Manual Download Page 43 | Manualshive

Page: 43 / 328

background image

1

Introduction

1-23

Backup and Restoration

Backup and Restoration

A standalone Configuration Backup and Restore (CBR) utility is
available for customers that do not use EFCM for backing up and
restoring user configuration data. You can use this utility to backup
and restore configuration data from all switch and director products
running E/OS versions 4.0 and higher. The CBR utility is available for
no charge in the Technical Documents section of the McDATA
website at

www.mcdata.com

or by contacting your sales

representative or service provider

The procedures for system backup and restoration are documented in
the

Configuration Backup and Restore Utility Installation and User Guide

(958-000370), which is also available at

www.mcdata.com

.

«
...
41
42
43
44
45
...
»

Summary of Contents for Enterprise Operating System









































































































































































































































































































































Reviews:

No comments

Related manuals for Enterprise Operating System

Brand: Canon Pages: 82

Powershot A650 IS

Brand: Canon Pages: 49

DEVICE FILTER MAC

Brand: FARONICS Pages: 4

SmartWare R2.00

Brand: Inalp Networks Pages: 321

Veriteq viewLinc 4.0

Brand: Vaisala Pages: 168

FLASH 8-USING FLASH VIDEO ENCODER

Brand: MACROMEDIA Pages: 30

SMART Notebook SE

Brand: SMART Pages: 20

Brand: Toshiba Pages: 1

dynadock Drivers

Brand: Toshiba Pages: 3

e-STUDIO Printer/Fax/Scanner/Copier

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 53

CLUSTER SUITE - FOR RHEL 4

Brand: Red Hat Pages: 74

SYSMAC CX-Programmer 9

Brand: Omron Pages: 232

CERTIFICATE 7.3 RELEASE NOTES

Brand: Red Hat Pages: 24

ANTI-VIRUS 2011 - REV 2011.11

Brand: AVG Pages: 209

Brand: Adaptec Pages: 133

Brand: Focusrite Pages: 35

Brand: Bay Networks Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands