McDATA Enterprise Operating System User Manual Download | Manualshive

Page: 291 / 328

background image

Commands and Corresponding Releases

B-1

B

Commands and

Corresponding Releases

Table B-1,

Commands and Releases

, shows the commands that are valid

in the Enterprise Operating System (E/OS) Command Line Interface
(CLI) and the release in which the command was added to the CLI.
The commands are organized by release, and are in alphabetical order
within the release.

Table B-1

Commands and Releases

First E/OS

Release

Command

7.0

config.features.NPIV

7.0

config.fencing.addPolicy

7.0

config.fencing.addPort

7.0

config.fencing.deletePolicy

7.0

config.fencing.removePort

7.0

config.fencing.setParams

7.0

config.fencing.setState

7.0

config.fencing.show

7.0

config.fencing.showTypeTable

7.0

config.ficonCUPZoning.addControlHost

7.0

config.ficonCUPZoning.deleteControlHost

7.0

config.ficonCUPZoning.setState

«
...
289
290
291
292
293
...
»

Summary of Contents for Enterprise Operating System









































































































































































































































































































































Reviews:

No comments

Related manuals for Enterprise Operating System

JUNOS PUS MOBILE SECURITY SUITE

Brand: Juniper Pages: 6

Discover ActiveX

Brand: Teklynx Pages: 165

DS-605 - VPN Client - PC

Brand: D-Link Pages: 15

DSN-210-SW - SureSync Continuous Data Protection

Brand: D-Link Pages: 4

Brand: D-Link Pages: 56

D-View 6 Professional

Brand: D-Link Pages: 143

Brand: D-Link Pages: 136

Brand: D-Link Pages: 279

Brand: IBM Pages: 590

Brand: Rane Pages: 8

Brand: Garmin Pages: 33

WorkCentre Pro 232

Brand: Xerox Pages: 64

Stylus Pro 5500

Brand: Epson Pages: 120

Brand: Lenovo Pages: 20

IBM Access Connections 3.3.0

Brand: Lenovo Pages: 28

Online Data Backup 1.8.14

Brand: Lenovo Pages: 52

Brand: Lenovo Pages: 24

Brand: Lenovo Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands