McDATA Enterprise Operating System User Manual Download | Manualshive

Page: 124 / 328

background image

2

2-80

Enterprise Operating System Command Line Interface User Manual

config

Output Example

The output from the config.switch.show command displays as
follows.

BB Credit: 2

R_A_TOV: 20

E_D_TOV: 4

Preferred Domain Id: 1

Switch Priority: Principal

Speed: 2 Gb/sec

Rerouting Delay: Enabled

Interop Mode: Open Fabric 1.0

Insistent Domain Id: Disabled

Domain RSCN: Enabled

Zoning RSCN: Disabled

Limited Fabric RSCN: Disabled

Zone FlexPars:

Fabric

config.switch.zoneFlexPars

Syntax

zoneFlexPars zoneFlexParstate

Purpose

This command configures the state of Zone Flex Pars.

Zoning RSCN

When enabled, allows zoning RSCNs to be sent
to registered members of the fabric.

Limited Fabric
RSCN

When enabled, fabric RSCNs are suppressed
after an IPL.

Zone Flex Pars

When set to fabric, RSCNs will only be sent to
affected fabric members when zoning
information changes. When set to none, filtering
of RSCNs will not take place, and RSCNs will
be sent to all zoneset members when zoning
information changes.

«
...
122
123
124
125
126
...
»

Summary of Contents for Enterprise Operating System









































































































































































































































































































































Reviews:

No comments

Related manuals for Enterprise Operating System

Venture IP Telephone System

Brand: Aastra Pages: 10

Brand: Garmin Pages: 6

Brand: AMX Pages: 54

Brand: Allied Telesis Pages: 668

CERTIFICATE SYSTEM 8.0 - ADMINISTRATION

Brand: Red Hat Pages: 564

FILES AND FOLDERS

Brand: Pfaff Pages: 8

Brand: AMX Pages: 24

Brand: FieldServer Pages: 11

VCLOUD REQUEST MANAGER

Brand: VMware Pages: 2

Multimaximizer L3-LL

Brand: Waves Pages: 26

Brand: Lenovo Pages: 100

Brand: Lenovo Pages: 6

REVIT ARCHITECTURE 2010

Brand: Autodesk Pages: 6

Brand: MACROMEDIA Pages: 10

Brand: Mackie Pages: 14

ICD-BP150 - Ic Recorder

Brand: Sony Pages: 68

PowerLite D6155W

Brand: Epson Pages: 6

Brand: Epson Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands