McDATA Enterprise Operating System User Manual Download Page 127

Page: 127 / 328

CLI Commands

2-83

config

Parameters

This command has one parameter.

Command Example

Root>

config system description McDATA Intrepid 6064

Fibre Channel Director

config.system.location

Syntax

location systemLocation

Purpose

This command sets the system location attribute.

Parameters

This command has one parameter.

Command Example

Root>

config system location Everywhere

config.system.name

Syntax

name systemName

Purpose

This command sets the system name attribute.

Parameters

This command has one required parameter.

Command Example

Root>

config system name Joe’s Switch

config.system.show

Syntax

show

systemDescription Specifies the new system description string for

the director or switch. The name can contain
0–255 characters.

systemLocation

Specifies the new system location for the
director or switch. The location can contain
0–255 characters.

systemName

Specifies the new system name for the director
or switch. The name can contain 0–24
characters.

Summary of Contents for Enterprise Operating System









































































































































































































































































































































Search results

Summary of Contents for Enterprise Operating System

Reviews:

Related manuals for Enterprise Operating System

Brands by name

Popular brands

McDATA Enterprise Operating System, User Manual

Search results

Summary of Contents for Enterprise Operating System

Reviews:

Related manuals for Enterprise Operating System

Brands by name

Popular brands