Mahindra Quanto Ems Diagnostic Manual Download Page 43 | Manualshive

Page: 43 / 333

background image

DIAGNOSTIC MANUAL MAN-00201

QUANTO

EMS

SEP 2012/Rev 1

The repair methods given by the manufacturer in this document are based on the technical specifications, current at the time of release. The methods may be modified as a result of changes introduced by the
manufacturer in the production of the various component units and accessories from which the vehicles are manufactured. The reproduction, translation, transmission, in part of or whole of the present document,
are prohibited without the prior written consent of Mahindra & Mahindra Ltd. The use of this document by any person other than the trained personnel, at the Authorized Service Centre of Mahindra & Mahindra Ltd.,
will amount to unauthorized use and shall be liable for penalty/prosecution

© 2012 Mahindra & Mahindra Ltd.

`

STEP 1

Connect the smart tester
Turn the ignition  ON
Initialise the diagnostic tool
Record the DTC and clear
Turn ignition  OFF
Turn ignition ON
Verify if   P0562 is present?

Is P0562 present?

Intermittent problem exists
Refer the intermittent problem
inspection procedure

STEP 2

Is the value = 11.0 to

14.5V?

STEP 3

Ignition OFF

Check and confirm  the proper
functioning of 5 A fuse (F47)  of
the EMS ECU   power supply
wire  from Ignition switch

EMS ECU wiring harness
connector (C4) DISCONNECTED
Ignition ON

Check the voltage between pin
71 of the EMS ECU wiring
harness connector and battery
ground

Is the value > 8 V?

STEP 4

Is the continuity

exists?

Ignition ON

Check the voltage between
battery positive and battery
negative

Suspect the charging circuit
Check and confirm the proper
functioning of charging
circuit(Alternator & Battery)
Clear the DTC and verify

Ignition OFF
EMS ECU wiring harness
connector (C4) DISCONNECTED
Ignition Switch wiring harness
connector (C113)
DISCONNECTED

Check the continuity between
pin 71 of the EMS ECU wiring
harness connector and pin 5 of
the ignition switch wiring
harness connector

Go to STEP 6

Examine the open circuit of
EMS ECU power supply wire
from ignition switch
Replace the wiring harness
Clear the DTC and verify

STEP 5

YES

YES

YES

NO

YES

NO

NO

NO

P 0562

43

«
...
41
42
43
44
45
...
»

Summary of Contents for Quanto














































































































































































































































































































































Reviews:

No comments

Related manuals for Quanto

Brand: GARO Pages: 23

LS4 Wallmounted

Brand: GARO Pages: 15

Brand: Carefree Pages: 12

Brand: Mobile Create Pages: 15

2011 Civic Sedan

Brand: Honda Pages: 5

990E0-54P56-000

Brand: Suzuki Pages: 12

Brand: Phonocar Pages: 2

Brand: Caltrend Pages: 2

Brand: Audiovox Pages: 1

EGR-3PVE-COLOUR

Brand: EGR Pages: 28

Brand: MASCOT Pages: 12

Brand: Honda Pages: 20

2009 Rio Series

Brand: Kia Pages: 219

Brand: Boyo Pages: 9

Brand: Westin Pages: 2

Brand: JBL Pages: 12

Brand: Needit Pages: 2

KIT ParkingSensor 814

Brand: Gemini Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands