Mahindra Quanto Ems Diagnostic Manual Download Page 68 | Manualshive

Page: 68 / 333

background image

DIAGNOSTIC MANUAL MAN-00201

QUANTO

EMS

SEP 2012/Rev 1

The repair methods given by the manufacturer in this document are based on the technical specifications, current at the time of release. The methods may be modified as a result of changes introduced by the
manufacturer in the production of the various component units and accessories from which the vehicles are manufactured. The reproduction, translation, transmission, in part of or whole of the present document,
are prohibited without the prior written consent of Mahindra & Mahindra Ltd. The use of this document by any person other than the trained personnel, at the Authorized Service Centre of Mahindra & Mahindra Ltd.,
will amount to unauthorized use and shall be liable for penalty/prosecution

© 2012 Mahindra & Mahindra Ltd.

`

STEP 1

Connect the smart tester
Turn the ignition ON
Initialise the diagnostic tool
Record the DTC and clear
Turn ignition OFF
Turn ignition ON
Verify if P0403 is present?

Is P0403 present?

Intermittent problem exists
Refer the intermittent problem
inspection procedure

STEP 2

Ignition OFF

Check and confirm the proper
function of 15 A fuse (F15) in
engine compartment fuse box

EGR modulator wiring harness
connector (C42) DISCONNECTED
Ignition ON

Check the voltage between
between pin 2 of EGR
modulator wiring harness
connector and battery ground

Examine the open circuit of
EGR modulator control wire
Replace the wiring harness
Clear the DTC and verify

Suspect EGR modulator internal
failure
Replace EGR modulator with a
new one.
Check and verify for any new
DTC’s

STEP 3

Ignition OFF
EGR modulator wiring harness
connector (C42) DISCONNECTED
EMS ECU wiring harness
connector(C4) DISCONNECTED

Check the continuity between
pin 1 of EGR modulator wiring
harness connector and pin 49 of
the EMS ECU wiring harness
connector

Is the continuity

exists?

Is the value =Vbat?

Examine the open/short to
ground of EGR modulator
power supply wire from main
relay
Replace the wiring harness
Check and verify for any new
DTC’s

NO

YES

NO

YES

NO

YES

P 0403

68

«
...
66
67
68
69
70
...
»

Summary of Contents for Quanto














































































































































































































































































































































Reviews:

No comments

Related manuals for Quanto

Brand: KC HiLiTES Pages: 4

Brand: Federal Signal Corporation Pages: 13

Brand: Dakota Digital Pages: 2

Brand: Dakota Digital Pages: 7

Brand: Uniden Pages: 16

Brand: Uniden Pages: 20

Brand: Lincoln Pages: 424

Brand: Volkswagen Pages: 26

Brand: Alpine Pages: 8

For 1985-1992 GM Cars and Trucks 17933

Brand: Edelbrock Pages: 4

Brand: Actia Pages: 37

signal mirror 2005-2009 Ford Mustang

Brand: muth Pages: 9

Brand: Condor Pages: 2

Brand: Lock'er Down Pages: 2

Brand: Blaupunkt Pages: 6

Outlander Plug-in hybrid

Brand: Mitsubishi Pages: 28

Brand: CITROEN Pages: 86

Brand: Carbest Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands