manualshive.com logo in svg

Mahindra Quanto, Ems Diagnostic Manual, Page: 292 / 333

Share
Download
Mahindra Quanto Ems Diagnostic Manual Download Page 292

DIAGNOSTIC MANUAL                                                                                                         MAN-00201

 

QUANTO                                                                     

EMS

                                                  

SEP 2012/Rev 1

 

 

The repair methods given by the manufacturer in this document are based on the technical specifications, current at the time of release. The methods may be modified as a result of changes introduced by the 
manufacturer in the production of the various component units and accessories from which the vehicles are manufactured. The reproduction, translation, transmission, in part of or whole of the present document, 
are prohibited without the prior written consent of Mahindra & Mahindra Ltd.  The use of this document by any person other than the trained personnel, at the Authorized Service Centre of Mahindra & Mahindra Ltd., 
will amount to unauthorized use and shall be liable for penalty/prosecution

© 2012 Mahindra & Mahindra Ltd.

 

 

` 

 

 

    CONTINIOUS TORQUE MONITORING 

 

DTC 

Description 

P1633 ECU 

Monitoring: PoI2 qty error 

P1634 ECU 

Monitoring:PoI2 shut off error 

P1635 ECU 

Monitoring:PoI3 

efficiency factor error 

P1637 ECU 

Monitoring: 

Injection quantity correction error 

P061B ECU 

Monitoring: 

Torque comparison error 

P163E ECU 

Monitoring: Torque monitoring level2 error 

P1639 

ECU Monitoring: Lead torque monitoring level2 error 

P163D 

ECU Monitoring: Set torque monitoring level2 error 

     

 

DTC  INFORMATION 

PROBABLE CAUSES OF 

FAILURE 

 NORMAL OPERATION 

 

Ignition  ON 

 

The voltage monitoring of the injector energizing time is 

found normal 

  

DTC DETECTING CONDITIONS

 

 

Ignition  ON 

 

EMS ECU supply voltage 8-16V 

 

The difference between the programmed energizing time 

and the measured energizing time exceeds the  limit 

  DTC REACTIONS 

 

 

Engine Check lamp continuosly  ON 

 HEALING CONDITION 

 

Ignition Off/On 

 

 
 
 

 

 

Faulty EMS ECU 

 

 

      

292

Summary of Contents for Quanto














































































































































































































































































































































Reviews:

No comments