manualshive.com logo in svg

Mahindra Quanto, Ems Diagnostic Manual, Page: 228 / 333

Share
Download
Mahindra Quanto Ems Diagnostic Manual Download Page 228

DIAGNOSTIC MANUAL                                                                                                         MAN-00201

 

QUANTO                                                                     

EMS

                                                  

SEP 2012/Rev 1

 

 

The repair methods given by the manufacturer in this document are based on the technical specifications, current at the time of release. The methods may be modified as a result of changes introduced by the 
manufacturer in the production of the various component units and accessories from which the vehicles are manufactured. The reproduction, translation, transmission, in part of or whole of the present document, 
are prohibited without the prior written consent of Mahindra & Mahindra Ltd.  The use of this document by any person other than the trained personnel, at the Authorized Service Centre of Mahindra & Mahindra Ltd., 
will amount to unauthorized use and shall be liable for penalty/prosecution

© 2012 Mahindra & Mahindra Ltd.

 

 

` 

 

P0501 

VEHICLE SPEED SENSOR PLAUSIBILITY ERROR 

     

    VEHICLE SPEED SENSOR (VSS) 

 

 

 

Vehicle Speed Sensor(VSS) is hall sensor type and senses the rotating speed of the transmission output 

shaft .  Comparing engine speed with vehicle speed calculated based on vehicle speed sensor signal, ECU 

recognizes engaged gear. Based on the information about engaged gear, ECU performs optimum fuel 

injection quantity correction 

DTC  INFORMATION 

PROBABLE CAUSES OF FAILURE 

 NORMAL OPERATION 

 

Ignition  ON 

 

When the vehicle is driven  , VSS outputs a pulse signal to  the 

EMS ECU  and is within the range 

DTC DETECTING CONDITIONS

 

 

Ignition  ON 

 

EMS ECU supply voltage 8-16V 

 

Clutch is engaged and gear not in neutral but the VSS sensor 

output remains same for more than calibrated time  

DTC REACTIONS

 

 

All the load dependent functions e.g. FBC, ZFC  are switched off 

 

Vehicle may feel jerky while driving 

HEALING CONDITION 

 

Ignition Off/On 

 

 

 
 

 

Short /open in VSS circuit 

 

 

Faulty   VSS 

 

 

 

        

228

Summary of Contents for Quanto














































































































































































































































































































































Reviews:

No comments