Mahindra Quanto Ems Diagnostic Manual Download Page 199 | Manualshive

Page: 199 / 333

background image

DIAGNOSTIC MANUAL MAN-00201

QUANTO

EMS

SEP 2012/Rev 1

The repair methods given by the manufacturer in this document are based on the technical specifications, current at the time of release. The methods may be modified as a result of changes introduced by the
manufacturer in the production of the various component units and accessories from which the vehicles are manufactured. The reproduction, translation, transmission, in part of or whole of the present document,
are prohibited without the prior written consent of Mahindra & Mahindra Ltd. The use of this document by any person other than the trained personnel, at the Authorized Service Centre of Mahindra & Mahindra Ltd.,
will amount to unauthorized use and shall be liable for penalty/prosecution

© 2012 Mahindra & Mahindra Ltd.

`

STEP 1

Connect the smart tester
Turn the ignition ON
Initialise the diagnostic tool
Record the DTC and clear
Turn ignition OFF
Turn ignition ON
Verify if P2138 is present?

Is P2138 present?

Intermittent problem exists
Refer the intermittent problem
inspection procedure

STEP 2

NO

YES

Ignition OFF
Accelerator pedal wiring
harness connector (C124)
DISCONNECTED
Ignition ON

Check the voltage between pin
2 of accelerator pedal wiring
harness connector and battery
ground

Is the value = 5±0.25

V?

STEP 3

I

Is the continuity

exists?

Examine the short circuit of
accelerator pedal sensor 1
power wire with battery ground
Replace the wiring harness
Clear the DTC and verify

Ignition OFF
Accelerator pedal wiring
harness connector (C124)
DISCONNECTED

Check the continuity between
pin 2 of accelerator pedal
wiring harness connector and
battery ground

YES

NO

Go to STEP 5

Ignition OFF
Accelerator pedal wiring
harness connector (C124)
DISCONNECTED
EMS ECU wiring harness
connector (C4) DISCONNECTED

Check the continuity between
pin 2 of accelerator pedal
wiring harness connector and
pin 18 of the EMS ECU wiring
harness connector

STEP 4

I

Is the continuity

exists?

Examine the open circuit of
accelerator pedal sensor 1
power wire
Replace the wiring harness
Clear the DTC and verify

Suspect EMS ECU malfunction
Replace EMS ECU with a new
one.
Check and verify for any new
DTC’s

YES

NO

NO

YES

P 2138

199

«
...
197
198
199
200
201
...
»

Summary of Contents for Quanto














































































































































































































































































































































Reviews:

No comments

Related manuals for Quanto

10-8002-C11998B

Brand: Saleen Pages: 12

2013 Buick Verano

Brand: Buick Pages: 5

Brand: Axxess Pages: 4

Brand: Vintage Air Pages: 14

Brand: SnapPad Pages: 5

Brand: B-Speech Pages: 24

MILSCO KIT# C746700

Brand: K&M Pages: 2

Brand: Car-Interface Pages: 25

2 Bike Carrier 977

Brand: Thule Pages: 6

Brand: Jeep Pages: 380

Brand: Cadillac Pages: 20

Brand: Hank Pages: 2

Brand: Mercedes-Benz Pages: 296

Brand: Bilstein Pages: 7

Brand: Jaeger Pages: 14

MAGICGRIP MGQDWD-CPO

Brand: Scosche Pages: 12

Brand: Painless Performance Pages: 16

Brand: EUFAB Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands