Mahindra Quanto Ems Diagnostic Manual Download Page 83 | Manualshive

Page: 83 / 333

background image

DIAGNOSTIC MANUAL MAN-00201

QUANTO

EMS

SEP 2012/Rev 1

The repair methods given by the manufacturer in this document are based on the technical specifications, current at the time of release. The methods may be modified as a result of changes introduced by the
manufacturer in the production of the various component units and accessories from which the vehicles are manufactured. The reproduction, translation, transmission, in part of or whole of the present document,
are prohibited without the prior written consent of Mahindra & Mahindra Ltd. The use of this document by any person other than the trained personnel, at the Authorized Service Centre of Mahindra & Mahindra Ltd.,
will amount to unauthorized use and shall be liable for penalty/prosecution

© 2012 Mahindra & Mahindra Ltd.

`

P0340

CAMSHAFT SENSOR NO SIGNAL ERROR

CAMSHAFT (SEGMENT SPEED) SENSOR

Hall Effect camshaft position sensor senses the Top dead center (TDC) point of the # 1 cylinder in the

compression stroke ,which allows the ECU to determine when to start the injection. The trigger is

mounted in the exhaust camshaft

DTC INFORMATION

PROBABLE CAUSES OF FAILURE

NORMAL OPERATION



Ignition ON



During engine cranking , the output signal received from cam

shaft position sensor to ECU is within the range

DTC DETECTING CONDITIONS



Ignition ON



EMS ECU supply voltage 8-16V



While engine cranking,no valid signal from camshaft position

sensor

DTC REACTIONS



Engine check lamp continuously ON.



Engine will not start



If this failure occurs when the engine is running then engine

will keep on running

HEALING CONDITION



Ignition Off/On



Open/short cam shaft
position sensor circuit



Faulty cam shaft position
sensor.



Malfunctioning EMS ECU

83

«
...
81
82
83
84
85
...
»

Summary of Contents for Quanto














































































































































































































































































































































Reviews:

No comments

Related manuals for Quanto

Brand: ZAPTEC Pages: 240

Brand: Baja Designs Pages: 6

MARTEN-FREE CAR

Brand: Gardigo Pages: 36

Brand: Alpine Pages: 69

Brand: Allen Sports Pages: 2

Brand: Thule Pages: 8

Brand: Metra Electronics Pages: 8

V70XC Cross country 1998

Brand: Volvo Pages: 262

Brand: ULTIMATE SPEED Pages: 40

Brand: v.link Pages: 19

2008 B2300 Truck

Brand: Mazda Pages: 280

Brand: Huf Pages: 6

Brand: Oldsmobile Pages: 248

PRIME DESIGN HRR3-E-PM52

Brand: Safe Fleet Pages: 12

Brand: Aries Pages: 3

Brand: Mazda Pages: 1001

Brand: Menabo Pages: 8

Brand: MiX Telematics Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands