manualshive.com logo in svg

Mahindra Quanto, Ems Diagnostic Manual, Page: 295 / 333

Share
Download
Mahindra Quanto Ems Diagnostic Manual Download Page 295

DIAGNOSTIC MANUAL                                                                                                         MAN-00201

 

QUANTO                                                                     

EMS

                                                  

SEP 2012/Rev 1

 

 

The repair methods given by the manufacturer in this document are based on the technical specifications, current at the time of release. The methods may be modified as a result of changes introduced by the 
manufacturer in the production of the various component units and accessories from which the vehicles are manufactured. The reproduction, translation, transmission, in part of or whole of the present document, 
are prohibited without the prior written consent of Mahindra & Mahindra Ltd.  The use of this document by any person other than the trained personnel, at the Authorized Service Centre of Mahindra & Mahindra Ltd., 
will amount to unauthorized use and shall be liable for penalty/prosecution

© 2012 Mahindra & Mahindra Ltd.

 

 

` 

 

    

   

STEP 1

Connect the smart tester
Turn the ignition  ON
Initialise the diagnostic tool
Record the DTC and clear
Turn ignition  OFF
Turn ignition ON
Verify if   P06A0 is present?

Is  P06A0 present?

Intermittent problem exists
Refer the intermittent problem 
inspection procedure

STEP 2

 STEP 3

Ignition OFF

Ensure the compressor relay is 
fixed properly in the connector 
of the ECU   fuse box
Remove the  AC compressor  
relay
Check the functioning of relay by 
providing 12V  to terminal 86 
and ground to terminal 85

Is a  clicking sound 

heard?

Replace the AC compressor  
relay with a new one
Clear the DTC and verify

Is the value = Vbat?

Ignition OFF
Remove the AC compressor  
relay 
Check the proper functioning of 
10 A fuse (F38)  and 10 A fuse 
(F16)
Ignition ON

Check the voltage   between pin 
5  of the AC compressor relay 
seating (C107) and battery 
ground
Check the voltage   between pin 
3  of the AC compressor relay 
seating (C107) and battery 
ground

NO

NO

NO

YES

YES

YES

Examine the open/short  circuit 
of AC compressor relay power 
wire from EMS  main relay and 
from ignition switch
 Replace the wiring harness
Clear the DTC and verify

Go to  STEP 4

 

P 06A0

295

Summary of Contents for Quanto














































































































































































































































































































































Reviews:

No comments