manualshive.com logo in svg

Mahindra Quanto, Ems Diagnostic Manual, Page: 262 / 333

Share
Download
Mahindra Quanto Ems Diagnostic Manual Download Page 262

DIAGNOSTIC MANUAL                                                                                                         MAN-00201

 

QUANTO                                                                     

EMS

                                                  

SEP 2012/Rev 1

 

 

The repair methods given by the manufacturer in this document are based on the technical specifications, current at the time of release. The methods may be modified as a result of changes introduced by the 
manufacturer in the production of the various component units and accessories from which the vehicles are manufactured. The reproduction, translation, transmission, in part of or whole of the present document, 
are prohibited without the prior written consent of Mahindra & Mahindra Ltd.  The use of this document by any person other than the trained personnel, at the Authorized Service Centre of Mahindra & Mahindra Ltd., 
will amount to unauthorized use and shall be liable for penalty/prosecution

© 2012 Mahindra & Mahindra Ltd.

 

 

` 

 

P0234 

BOOST PRESSURE CONTROLLER DEVIATION BELOW MINIMUM LIMIT 

     

 

    

  

DTC  INFORMATION 

PROBABLE CAUSES OF FAILURE 

 NORMAL OPERATION 

 

Ignition  ON 

 

The permissible negative control deviation of the closed loop 

boost pressure control is with in the limit 

 DTC DETECTING CONDITIONS 

 

Ignition  ON 

 

EMS ECU supply voltage 8-16V 

 

Negative control deviation of the closed loop boost pressure is 

below the minimum  limit. 

 DTC REACTIONS 

 

 EGR Shuts OFF 

 

 Engine Check lamp continuously ON 

 HEALING CONDITION 

 

Ignition Off/On 

 

 
 

 

Blocked vent hose of  boost 

pressure actuator 
 

 

Faulty boost pressure 

actuator 
 

 

  

 

    

CORRECTIVE ACTION 

 

 

Check for  any  blockage in vent hose of boost pressure actuatorand  if found ,  rectify it 

 

 

 If the problem still exists , replace the boost pressure actauator with new one 

 

 

 

 

 

 

 

 

262

Summary of Contents for Quanto














































































































































































































































































































































Reviews:

No comments