Lada Kalina User Manual Download Page 39

Page: 39 / 168

INSTRUMENT CLUSTER

1 –

tachometer.

It indicates the

speed of the engine shaft (x1000
min

-1

If the tachometer needle is in the

area of red scale it warns of in-
creased engine speed. To prevent
damage to the engine its maximum
speed is limited with electronic en-
gine control system programme. If
exceeding the speed of approxi-
mately 6200 min

-1

fuel supply will be

limited. In this case, possible engine
conks and traffic blows are not a fail-
ure. By reducing the speed the fuel
supply will be resumed.

Also, do not run the engine when

starting and driving with engine shaft
speed of below 800 min

-1

ATTENTION!

Do not run the engine in dan-

gerous mode – with the engine
shaft speed of above 6200 min

-1

and below 800 min

-1

2 –

«Engine» LED.

It lights orange

when the ignition is on and after
engine start it goes out.

With the engine running

lighting

of the LED does not mean that the
engine must be stopped immediate-

ly – the controller has back-up
modes, which allow the engine to
operate in conditions close to nor-
mal.

ATTENTION!

However, the cause of the fault

must be corrected at any certified
SSNE as quickly as possible.

3 –

left turn indicator LED.

blinks green when switching on left
turn indicators.

4 –

oil pressure warning switch.

It lights red when switching on the
ignition and after engine start it goes
out.

With the engine running

lighting

LED and intermittent horn of the

Fig. 31. Instrument cluster

Summary of Contents for Kalina









































































































































































Search results

Summary of Contents for Kalina

Reviews:

Related manuals for Kalina

Brands by name

Popular brands

Lada Kalina, User Manual

Search results

Summary of Contents for Kalina

Reviews:

Related manuals for Kalina

Brands by name

Popular brands