Lada Kalina User Manual Download Page 45

Page: 45 / 168

GEARSHIFT PROMPTER

FUNCTION

Gearshift prompter (GP) – func-

tion that determines the necessity to
change gear for higher or lower gear
(for guarantee the engine most
economy mode) and informs the
driver of it.

This function can be used for cars

with manual gearbox (MGB) only.

Sound gearshift prompter

switch on/off

The sound signal on/off can be

done by key «Reset» or «ОК»

(in

design variant)

at the under-steer-

ing switch. The GP sound signal sta-
tus is indicated at the instrument
cluster LCD in the on-board comput-
er row.

Information displayed at LCD:
– «

GSI 0

» – GP sound is switched

off;

– «

GSI I

» – GP sound is switched

on.

LCD reading in «norm» version

Recommended gear shift indication

Gearshift prompt

LCD reading mode

minimal

maximal

LCD reading

1–6

It is recommended to drive-down

No recommendation, the function is switched on

8–14

It is recommended to drive up

7, 15

The function is switched off, no indication

Signal reading

Recommendation

Fig. 32. GP function in the instrument cluster LCD

Summary of Contents for Kalina









































































































































































Search results

Summary of Contents for Kalina

Reviews:

Related manuals for Kalina

Brands by name

Popular brands

Lada Kalina, User Manual

Search results

Summary of Contents for Kalina

Reviews:

Related manuals for Kalina

Brands by name

Popular brands