Lada Kalina User Manual Download Page 137

Page: 137 / 168

135

Extension of table 9

Engine model

21126

11186

21126

Unladen weight, kg

– Min, kg

1025

– Max, kg

1085

Gross Vehicle Weight Rating (GVWR), kg

1560

Road clearance at full load under the engine

not less 182

not less 160

case, mm

Road clearance at full load under the transmission

not less

housing (MT/AT), mm

187

165

145

Maximum speed

, km/h

174

165

168

178

175

Acceleration time up to 100 km/h, sec

11,3

12,2

11,5

13,1

Gross trailer weight

– without brakes, kg

450

– with brakes, kg

900

750

Measured by special technique.

Provided that the vehicle is equipped with towing hitch in accordance with the requirements of UNECE Regulation No 55-01.

Version

Luxe Cross

Norm Cross

Norm

Luxe

Summary of Contents for Kalina









































































































































































Search results

Summary of Contents for Kalina

Reviews:

Related manuals for Kalina

Brands by name

Popular brands

Lada Kalina, User Manual

Search results

Summary of Contents for Kalina

Reviews:

Related manuals for Kalina

Brands by name

Popular brands