Lada Kalina User Manual Download Page 144

Page: 144 / 168

142

Ta b l e 2

ENGINE OIL

Based on the table below, determine the level of quality

and oil viscosity grade, prescribed for your vehicle in accor-
dance with the existing operating temperature range.

If necessary – change the oil. For this purpose refer to the

authorized service center.

Use only recommended operating and lubricating fluids. For information on the recommended operating and lubricating fluids,

refer to the authorized service center.

Filling point

Engine lubrication

system

Description

Minimum temperature of cooling medium under

the vehicle operation

SAE J 300 viscosity

grade

Maximum environment temperature under the

vehicle operation,

Engine oil

SAE viscosity grades and operating temperature range

The quality level of operational properties: API SL/АPI SM/API SN

СТО ААИ 003 Б5/СТО ААИ 003 Б6

-40

0W-30

-40

0W-40

–30

5W-30

–30

5W-40

–25

10W-30

–25

10W-40

–20

15W-40

–15

20W-40

–15

20W-50

up 45

Summary of Contents for Kalina









































































































































































Search results

Summary of Contents for Kalina

Reviews:

Related manuals for Kalina

Brands by name

Popular brands

Lada Kalina, User Manual

Search results

Summary of Contents for Kalina

Reviews:

Related manuals for Kalina

Brands by name

Popular brands