pressing and holding one of the but-
tons
1–6
till the number is displayed
in the middle of the line.
5.6.3 To call the saved number it is
necessary to pass to «Telephone»
mode, shortly pressing
button
(Fig. 2, pos. 10). Then chose the
desired number pressing one of the
buttons
1–6
and the number will be
displayed in the lower line. To con-
firm the choice shortly press
button of number dialing confirma-
tion
(Fig. 2, pos. 10).
Note.
The phone numbers saved may
be deleted from memory by resetting
radio system to factory settings (part 6.3
«System settings»).
6. Setting mode
6.1 Audio parameters setting
6.1.1 Press encoder short while in
the «main screen» (display screen) to
enter this mode.
6.1.2 Turn encoder in the follow-
ing order to switch and to change
parameters: Equalizer
→
Low
Frequency Tone
→
High Frequency
Tone
→
Balance
→
Balance
front/rear
→
Tone compensation
→
Exit.
(
(
Note.
If user does not make any
adjustments during 5 minutes, the setting
mode turns off automatically.
6.2 Screen for adjustment
of selected audio parameter
6.2.1 Press encoder in the
respective menu item to enter this
mode. Turn encoder knob to adjust
selected parameter.
6.2.2 Equalizer is set in the follow-
ing order:
EQ JAZZ
→
EQ POP
→
EQ CLAS-
SICS
→
EQ VOCAL
→
EQ USER.
6.2.3 Tone adjustment range LF,
HF, Balance, Balance front/rear is
from «
‒
7» to «+7» units.
6.3 System settings
6.3.1 By means of system settings
you can:
– set time displaying format (time
mode);
– set the current time manually
(hours/minutes setting);
– turn on/off the current time
adjustment by RDS signals (RDS
CT);
– turn on/off the function of auto-
matic switching to the alternative
broadcast frequency (RDS AF);
– turn on/off the function of radio
stations seeking based on the set
program type (RDS PTY);
– turn on/off the function of local
stations receiving (RDS REG);
– turn on/off of mid-band range
(AM- range);
– turn on/off of
Bluetooth
func-
tion (tel. connection);
– turn on/off of buttons pressing
acknowledgement signal (signal);
– turn on/off of noise suppression
function (noise suppression);
– reset radio settings to the facto-
ry settings (reset).
6.3.2 Press encoder long to enter
system setting mode while in the
«main screen» (display screen). Turn
encoder to select the available set-
tings and adjust the selected param-
eter. Press encoder short to adjust
the selected parameter and ackno-
wledge the setting.
6.3.3 You can quit the system set-
tings mode through the menu item
«Quit» or automatically (if no adjust-
ments are performed during 5 min-
utes).
7. Non-warranty cases
7.1 Non-warranty cases are spec-
ified in the Table 4.
155
Summary of Contents for Kalina
