Kikusui PAT160-25T, Operation Manual

Page: 13 / 218

PAT-T 4kW
xi
1
2
3
4
5
6
7
8
9
Appx
Contents by Function
Preparation
Operation
Sit u ation Heading
Page
Ho w do I check the accessories. 2.1, “Checking the Package Contents” 2-2
The installation space is limited. Ho w m u ch space is needed
aro u nd the air inlet and o u tlet?
2.2, “Preca u tions Concerning Installation” 2-3
Ho w do I connect the AC po w er s u pply? 2.5, “Connecting the Po w er Cable” 2-6
What kind of w ires sho u ld be u sed to connect to the AC po w er
s u pply?
2.5, “Connecting the Po w er Cable” 2-6
Ho w can I u se the PAT in the single-phase inp u t ? “2.6 T u rning On
“4.7 CO N FIG Settings
“7.12 Other System Config u ration
2-9
4-21
7-27
Ho w do I change the phase inp u t mode?
(from the single-phase inp u t to the three-phase inp u t)
“4.7 CO N FIG Settings
“7.12 Other System Config u ration
4-21
7-27
Ho w do I change the phase inp u t mode?
(from the three-phase inp u t to the single-phase inp u t)
“4.7 CO N FIG Settings
“7.12 Other System Config u ration
4-21
7-27
What kind of w ires sho u ld be u sed to connect the load? 3.2, “Load Cable” 3-4
The w ire connecting the load is long (distance to the load is
long), b u t stable voltage is req u ired.
4.11, “Remote Sensing F u nction” 4-26
Ho w do I set the comm u nication conditions for remote control? 7.4, “Interface Set u p” 7-4
Ho w do I control the o u tp u t voltage u sing an external DC
voltage?
5.4.1, “External Voltage (Vext) Control” 5-9
Ho w do I increase the c u rrent capacity in parallel operation? 6.1, “Master-Slave Parallel Operation” 6-2
Ho w do I rack mo u nt the PAT? What kind of parts is needed? “ Options” 1-4
Sit u ation Heading
Page
Ho w can I u se the PAT as a constant voltage po w er s u pply
(CV)?
4.5, “Using the PAT as a CV or CC Po w er
S u pply (Setting the O u tp u t Voltage and O u tp u t
C u rrent)”
4- 8
Ho w can I u se the PAT as a constant voltage c u rrent s u pply
(CC)?
I w o u ld like to operate the PAT at a given voltage. Ho w do I
register the voltage in the preset memory?
4. 8 , “Preset Memory F u nction” 4-24
When u sing the PAT in the single-phase inp u t mode, is there
any difference in the setting range compared to the three-
phase inp
u t po w er?
“4.5 Using the PAT as a CV or CC Po w er S u pply
(Setting the O u tp u t Voltage and O u tp u t C u rrent)
“4.6.1 Overvoltage protection (OVP) and
overc
u rrent protection (OCP)
4- 8
4-10
Ho w do I set the u pper limit to prevent the voltage from being
increased too m u ch?
“ Setting limit f u nction” 4-11
Ho w do I set the voltage in fine resol u tion? “ Fine adj u stment f u nction” 4-9
Ho w do I set the protection f u nction to prevent damage to the
load?
4.6, “Protection F u nctions and Alarms” 4-9
4.6.1, “Overvoltage protection (OVP) and
overc
u rrent protection (OCP)”
4-10
Ho w do I c u t off the o u tp u t at a different time from other po w er
s u pplies?
“ O u tp u t on/off delay f u nctions” 4-5
Ho w can I monitor the o u tp u t voltage and o u tp u t c u rrent? 5. 8 , “External Monitoring” 5-21
Ho w do I temporarily lock the keys? 4.9, “Lock F u nction” 4-25
Ho w do I u se the sample program for remote control? A.7, “Sample Programs” A-27
Ho w do I reset the PAT to factory defa u lt settings? 4.12, “Factory Defa u lt Settings” 4-29
See
See