JAC A-CLASS Manual Download

Page: 107 / 176

Worse conditions include but not
limited to:

◇

Frequent cold starting

◇

Frequent start and stop when the

traffic is jammed.

◇

Frequent short-distance drives.

◇

Frequent drives when environm

-ental temperature is below the
freezing point.

◇

Long term idle speed.

◇

Frequent low speed drives.

◇

Drives under dusty condition.

Air filter/filter element

Regularly check and replace filter
member of air filter according to the
maintenance regulation herein.

Notes

◇

Correct

operation

the

engine requires clean air.

◇

Do not drive any vehicle

without filter member of air filter.

◇

Driving a vehicle without filter

member

air

filter

will

damage the engine.

◇

Original parts of JAC shall be

used while replacing the air
filter.

107

Summary of Contents for A-CLASS

















































































































































































Search results

Summary of Contents for A-CLASS

Reviews:

Related manuals for A-CLASS

Brands by name

Popular brands

JAC A-CLASS, Manual

Search results

Summary of Contents for A-CLASS

Reviews:

Related manuals for A-CLASS

Brands by name

Popular brands