manualshive.com logo in svg

Intec MLC 8000, Operating Manual

Share
Download
Intec MLC 8000 Operating Manual Download Page 95

INTEC GmbH  

 

 

 

 

    22/12/2016 

Lift controller MLC 8000 

 

Operating manual V2.0

 

 

 

95/196 

Nr. 

Error message 

Description 

Lift controller reaction 

- Frequently switching inputs 
- Errors in the controller 
software 

129/100  No conn. to COP 

No CAN bus data transmission 
to TSE boards inside car 
operation panel COP. 
Possible reasons: 
- TSE defective 
- COP not connected 
- CAN bus line disturbed 

Lift continues operation. 
Internal test of data transmission 
 

129/128  Overrun RS232 

Data overflow on RS232 
interface (too much incoming 
data in short time) 

 

129/129  Offl.Err.RS232 

Disturbing signals on RS232 in 
offline mode 

 

129/130  Onl.Err.RS232 

Disturbing signals on RS232 in 
online mode 

 

129/131  CRC error RS232 

Invalid data received (wrong 
checksum) on RS232 

 

129/144  Overrun iModul 

Data overflow on iModul 
 (Modem, Ethernet, ...) 

 

129/145  Offl.Err.iModul 

Disturbing signals on iModul 
 (Modem, Ethernet, ...) in offline 
mode 

 

129/146  Onl.Err.iModul 

Disturbing signals on iModul 
 (Modem, Ethernet, ...) in online 
mode 

 

129/147  CRC error iModul 

Invalid data received (wrong 
checksum) on iModul 
 (Modem, Ethernet, ...) 

 

130/48  Mult. group no. 

There are 2 HSE modules with 
the same group number in a lift 
group 

The lift continues, however, 
landing calls and group control do 
not work properly. 

144/1 

Min.pressure  

For hydraulic lifts: oil pressure 
below the limit (input 
"Min.pressure" activated). 

Emergency stop. 
Back to normal operation if input is 
deactivated again. 

144/2 

Max.pressure 

For hydraulic lifts: oil pressure 
above the limit (input 
"Max.pressure" activated). 

Emergency stop. 
Back to normal operation if input is 
deactivated again. 

144/16  Overload 

Lift overloaded 

Only measured if lift is located in a 
floor with open doors. 
Back to normal operation if 
overload input is off. 

160/0 

Drive error 

Fault signal from the drive at 
standstill state. 

Error state. 
Back to normal operation if fault 
signal is deactivated. 

161/0 

Drive err.move 

Fault signal from the drive 
while moving. 

Emergency stop. 
Back to normal operation if fault 
signal is deactivated. 

Summary of Contents for MLC 8000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands