manualshive.com logo in svg

Intec MLC 8000, Operating Manual

Share
Download
Intec MLC 8000 Operating Manual Download Page 104

INTEC GmbH  

 

 

 

 

    22/12/2016 

Lift controller MLC 8000 

 

Operating manual V2.0

 

 

 

104/196 

Nr. 

Error message 

Description 

Lift controller reaction 

error or after inspection trip). 

176/112  OP device err. 

Faulty condition of the OP 
device (e.g. set both limit 
switches) 

Back to normal operation if OP 
device has defined state again. 

176/113  OP device ramp 

OP-device is unlocked while 
the lift wants to start 

See above 

176/114  OP dev. not out 

OP device can't move out 

See above 

176/115  OP dev. not in 

OP device can't move in 

See above 

176/116  OP dev. ramp on 

Ramp of OP device can't move 
out 

See above 

176/117  OP dev. ramp off 

Ramp of OP device can't move 
in 

See above 

176/128  Uncontr.movement 

Lift moved out of the door zone 
while the doors are open 
 (see EN81 Annex A3) 

Out of operation. 
Back to normal operation only by 
operationg a special Reset switch 
or by switching on emergency 
recall operation. 

176/129  Input unc.move 

Lift controller has recognized 
uncontrolled movement, but the 
input to check the uncontrolled 
movement state has not 
switched on. 
 

Out of operation. 
Back to normal operation only by 
operationg a special Reset switch 
or by switching on emergency 
recall operation. 

176/131  No deceleration 

Lifts with slow down control 
circuit: Lift didn't slow down to 
defined speed at the final floors 

Emergency stop 
Back to normal operation after a 
few seconds. 

176/132  Dec.circ.not off 

Lifts with slow down control 
circuit: Control circuit still 
triggered at standstill 

Back to normal operation if control 
circuit has right state again 

176/144  LIMAX Floortab 

If using LIMAX Safe as 
positioning system: Position 
difference between LIMAX 
Safe and HSE 

Emergency stop 
New setup procedure necessary 

176/145  LIMAX Insp.sig 

If using LIMAX Safe as 
positioning system: Inspection 
signal inputs of LIMAX Safe 
wrong 

Check wiring of LIMAX Safe 

176/146  LIMAX Relay test 

If using LIMAX Safe as 
positioning system: The cyclic 
relay test takes  unusually too 
long 

Check LIMAX Safe; if this occurs 
repeatedly,change LIMAX 

192/1 

Trip time out  

Time between 2 state changes 
of shaft switches SGM (door 
zone) exceeded (Trip time 
monitoring according to EN81; 
parameter "Triptime[s]"). 

Emergency stop, out of operation 

192/2 

LS or callmisuse  

Number of trips on car calls, in 
which the light screen has not 
been interrupted, exceeded 

All car calls cleared; no further 
error reaction 

Summary of Contents for MLC 8000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands