manualshive.com logo in svg

Intec MLC 8000, Operating Manual

Share
Download
Intec MLC 8000 Operating Manual Download Page 45

INTEC GmbH  

 

 

 

 

    22/12/2016 

Lift controller MLC 8000 

 

Operating manual V2.0

 

 

 

45/196 

1. Menu level 

2. Menu level 

3. Menu level 

4. Menu level 

Description 

 

 

 

Check 

↑

 [mm] 

Position below the level position of top floor, where a folding apron 

must be fully unfolded again 

 

 

 

Check 

↓

 [mm] 

See above; setting for bottom floor 

 

 

 

Get apr.[mm] 

Position below bottom floor for getting an automatic folding apron. 

If this setting is not equal 0, than the lift will always go down up to this 

positionto get the folding apron, even if the feedback contact from 

apron is already switched on. 

 

 

 

Governor 

When using the overspeed governor with additional magnetic coil for 

protection against uncontrolled movement: 

always: The coil on the over speed governor is only switched off in 

case the shelter monitoring has been triggered. 

moving: The coil on the over speed governor is switched on while the 

lift is moving. 

mov.+DZ: The coil on the over speed governor is switched on while 

the lift is moving and while the lift stops inside the door zone 

 

 

 

Govern.[ms] 

If a feedback contact exits on the over speed governor: Maximum 

waiting time  for feedback contact while switching on and off. 

If no feedback contact exists: delay time after switching the output 

"Governor" on or off. 

 

 

Holding bolts 

 

Parameters for lifts with holding bolts 

 

 

 

Hold.bolts 

Specifies whether the lift is equipped with holding bolts (yes / no) 

 

 

 

Stop pos.[mm] 

Specifies how many mm  lift should stop when entering a floor above 

this floor, so that the holding bolts can be pulled out or how many mm 

the lift has to move up to bring in the holding bolts before starting a 

new trip. 

 

 

 

Stop min[mm] 

Minimum distance above a floor to pull in / pull out the holding bolts. 

 

 

 

Stop max [mm] 

Maximum distance above a floor to pull in / pull out the holding bolts. 

 

 

 

Hold.zone[mm] 

Area in mm where the lift could  reached the holding position. 

 

 

 

Repeat hold. 

Indicates, if the lift should move down again if the lift is still in holding 

zone (see above), but the signal "Holding reached" did switch off. 

 

 

 

Pump.del[ms] 

Delay time by hydraulic lifts to start hydraulic pump again, if low 

pressure is detected whilem the lift is in holding position. 

 

 

 

Pump.off[mm] 

Position above the level position where the hydraulic re-pumping is 

switched off again at the latest (see also parameter above). In the 

normal case, the pump is, however, turned off when the pressure loss 

is compensated. 

 

 

 

Relays 

Switching status of the holding bolts relays after the holding bolts are 

Summary of Contents for MLC 8000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands