manualshive.com logo in svg

Intec MLC 8000, Operating Manual

Share
Download
Intec MLC 8000 Operating Manual Download Page 51

INTEC GmbH  

 

 

 

 

    22/12/2016 

Lift controller MLC 8000 

 

Operating manual V2.0

 

 

 

51/196 

1. Menu level 

2. Menu level 

3. Menu level 

4. Menu level 

Description 

 

 

 

Dec.extens. 

↓

 

See above; for downwards direction 

 

 

Car fan 

 

 

 

 

 

Fan mode 

autom.: The cabin fan is switched on automatically at the trip start and 

switched off at trip end with a time delay (see next parameter). 

manual: The cabin fan is turned on and off with a fan switch. By this 

setting, a max. duration (see the next parameter) can be programmed. 

 

 

 

Time [s] 

At automatic fan mode (see above): Time delay before switching off 

the fan after every trip. 

At manual  fan mode :maximum switched on time. If the time is set to 

0, then the fan is not switched off automatically. 

 

 

Interm.door 

 

 

 

 

 

While moving 

yes: intermediate door is monitored while moving. If this intermediate 

door opens while moving, the lift will clear all calls and stops in the 

next floor. At the same time, an error message is set in the error stack. 

no: intermediate door is monitored only during standstill. 

 

 

Car display 

 

Settings for the car level display 

 

 

 

Overload 

Indicates, if overload should be displayed at the landing. At a level 

indicator inside the car overload is always displayed. 

 

 

 

Non-smoke CC 

Specifies , whether the "Non smoking sign" is displayed on the level 

display inside car (currently only available on LCD display LCI16) 

 

 

 

Non-smoke LC 

Specifies , whether the "Non smoking sign" is displayed on the level 

display at the landings (currently only available on LCD display LCI16) 

 

 

 

Inspection 

Indicates whether the inspection state and emergency recall operation 

state to be displayed on the indicator. 

 

 

 

Out of order 

Specifies whether to display "Out of order" on the indicator 

 

 

 

Fault 

Specifies whether to display a fault state on the indicator 

 

 

 

Buzzer 

Function of the integrated buzzer on some level indicators: 

- Load: Buzzer sounds in case of  overload 

- Door: buzzer sounds during forced door closing (light screen 

ignored) 

- Car call: buzzer sounds briefly as an acoustic car call indication 

Any combination of these 3 functions are possible 

 

 

 

Targ.dist. 

Specifies at what distance before floor level (in mm), the level display 

is switched to the nexgt floor. 

If this parameter is set to 0, level display switches to next floor at 2/3 

of the distance between this floors. 

 

 

Gong 

 

 

Summary of Contents for MLC 8000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands