manualshive.com logo in svg

Intec MLC 8000, Operating Manual

Share
Download
Intec MLC 8000 Operating Manual Download Page 20

INTEC GmbH  

 

 

 

 

    22/12/2016 

Lift controller MLC 8000 

 

Operating manual V2.0

 

 

 

20/196 

1. Menu level 

2. Menu level 

3. Menu level 

4. Menu level 

Description 

 

 

Wt.CC Main[s] 

 

Time until door closing when the lift has approached a floor due to a 

car call (just for main floor; see above) 

 

 

Wt.LC Main[s] 

 

Time until door closing when the lift has approached a floor due to a 

landing call (whether simultaneously a car call existed). 

(just for main floor; see above) 

 

 

Wt.nC Main[s] 

 

 If the lift is on a floor and there is no further call, then the lift closes 

after this time the doors after that time (unless "Parking with open 

door" is set; see Door parameters) 

(just for main floor; see above) 

 

 

Doorstop[s] 

 

Time Door Stop push stays active until pressed 

 

 

Wt.Start[ms] 

 

Start delay after closing of the safety circuit of the shaft doors 

("Debouncing") 

 

 

Wt.door[s] 

 

Max. w aiting time for safety circuit doors when starting 

 

 

 

Errdelay[s] 

 

Waiting time between the occurrence of an error and further reactions 

of the lift controller (call canceling, setting the fault relay, sending an 

error message via the remote data transmission, etc.) 

 

Drive parameter 

 

 

 

 

 

General 

 

 

 

 

 

Drive 

Selection of interface between lift controller and drive unit: 

- Standard: control of the drive only  via relays of the main board 

- CAN-Lust: Inverter "Lust" connected by CAN bus 

- CAN-ASE: Using an ASE board (UEA) as interface to lift controller 

- CAN-Open: Inverter interface according to CANopen Lift (DSP 417) 

- Em.RS485: Emerson inverter connected by RS485 

 

 

 

Star/D. [ms] 

Changeover time star / delta (hydraulic lifts) 

 

 

 

Startdel[ms] 

Delay between switching on running contactors and setting control 

signals (only if parameter "Sign.delayed" (see below) is set to "Yes" at 

the same time) 

 

 

 

Brakedel[ms] 

Delay between setting control signals and switching on brake 

contactor 

 

 

 

Brakeoff[ms] 

Delay between switching off the control signals and brake contactor  

 

 

 

Offdel. [ms] 

Delay between switching off brake contactor and main / direction 

contactor 

 

 

 

Stopdel.[ms] 

Delay between switching off all contactors and dir enable 

signals 

 

 

 

Stop    [ms] 

Waiting time after shutdown of all control signals and contactors until 

Summary of Contents for MLC 8000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands