manualshive.com logo in svg

Intec MLC 8000, Operating Manual

Share
Download
Intec MLC 8000 Operating Manual Download Page 41

INTEC GmbH  

 

 

 

 

    22/12/2016 

Lift controller MLC 8000 

 

Operating manual V2.0

 

 

 

41/196 

1. Menu level 

2. Menu level 

3. Menu level 

4. Menu level 

Description 

 

 

Firemen run adj. 

 

Parameter for fireman trip 

 

 

 

Door cl. 

Operation of the door closing in fireman mode: 

auto: The door closes automatically to start a trip 

pulse: The door is not closed until the close-door-button was pressed 

shortly. 

stop: The door is closed only when the door-close-button is pressed 

and held down. Releasing the button stops the door. 

reverse: Door is closed only when the door-close-button is pressed 

and held. When releasing the button, the door opens again as long as 

she was not completely closed 

 

 

 

Door op. 

See above; handling of door opening 

 

 

 

Door firefl. 

Operation of the door (opening and closing) in fireman floor (main 

floor): 

auto:In the fireman floor the door opens and closes during firefighting 

operation alwaysautomaticallyl, regardless of the settings described 

above. 

fire: In the fireman floor the door opens and closes like defined in the 

above setting for all other floors (auto/pulse/stop/reverse). 

 

 

 

Retrieve car 

yes: if the lift is already in the fire service operation, the lift can be 

called back by re-activating the fire call in the fireman floor. 

no: The lift can not be called back into the fireman floor once fire 

operation has been started. 

 

 

 

Autofiremode 

yes: After reaching the fireman floor the lift will go to fireman 

operation automatically. 

 no: To start fireman operation a separate key switch is necessary 

inside car panel. 

 

 

 

Auto-normal 

Indicates whether the lift (if fire brigade call is available after returning 

to the fire floor) returns to normal operation after turning off the 

fireman key switch. If "No", a reset is required. 

 

 

Hazardous goods 

 

 

 

 

 

Car calls 

yes: Targeted selection is done via car calls 

No: Separate hazardous calls are necessary. 

 

 

 

Car fan 

normal: cabin fan works even when transporting dangerous goods as 

in the default mode. 

always: During a hazardous transport, the cabin fan is running 

constantly 

Never: During a hazardous transport, the cabin fan is always off. 

 

 

 

Fireman mode 

yes: Fireman service has higher priority than hazardous transportation 

Summary of Contents for MLC 8000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands