Intec MLC 8000 Operating Manual Download Page 89 | Manualshive

Page: 89 / 196

background image

INTEC GmbH

22/12/2016

Lift controller MLC 8000

Operating manual V2.0

89/196

4.14 Error messages

Nr.

Error message

Description

Lift controller reaction

16/1

AWG Band decekt

magnetic tape of the absolute
encoder AWG defective

Check tape and change if
necessary.
For a detailed error analysis see
manual of AWG

32/112 Pos. Defect

Defective positioning system

Emergency stop
This error message appears, for
example, if the magnetic tape of
the AWG is torn.

32/112 AWG defect

positioning system (absolute
encoder AWG) defective

Emergency stop
Lift continues operation if AWG
has reset the error.
For a detailed error analysis see
manual of AWG.

49/0

Phase off

Phase error (signal of an
external power supply monitor
device)

Emergency stop; then out of
service

49/1

Car light off

Car light power supply is
missing

Rope lift: Stop in next floor

Hydraulic lift: Trip to lowest floor

Return to normal operation when
car light power is on again.

50/0

Accu power

24V power supply off. All other
errors are ignored in this state.

Emergency stop, , then error state.
Automatic return to normal
operation when power is on.

52/0

SL off

Safety line open due to a fault. Error state “SL off”.

Automatic return to normal
operation when the safety circuit is
closed again.

52/1

SL off trip

Safety line open due to a fault
while the lift was moving.

Emergency stop; then error state
“SL off”.
Automatic return to normal
operation when the safety circuit is
closed again.

52/2

SL door off

Safety line of revolving shaft
door, car door or automatic
shaft door is missing while the
lift wants to start a trip.

Waiting time of 4 seconds, then lift
controller opens the doors and
closes again.

52/3

SL final limit

Lift (probably) in final bottom
limit switch.
The error message is
generated when the primary
safety circuit is missing, while
the lift is above top floor level
or below bottom floor level (see
parameters "Top limit" and
"Bot.limit" in "General

Rope lift: Back to normal operation
if limit switch is closed.

Hydraulic lift: If safety line is closed
again lift goes to lowest floor and
stops operation.

«
...
87
88
89
90
91
...
»

Summary of Contents for MLC 8000





































































































































































































Reviews:

No comments

Related manuals for MLC 8000

Brand: Balboa Instruments Pages: 10

Brand: Quantum Data Pages: 36

Brand: National Instruments Pages: 29

Brand: National Instruments Pages: 40

Brand: National Instruments Pages: 28

Brand: National Instruments Pages: 7

Brand: National Instruments Pages: 22

Brand: U-Prox Pages: 3

Brand: U-Prox Pages: 25

Brand: U-Prox Pages: 2

FSDrive-MV1000 Series

Brand: YASKAWA Pages: 260

Brand: YASKAWA Pages: 114

Brand: YASKAWA Pages: 20

Brand: YASKAWA Pages: 152

Brand: YASKAWA Pages: 66

Brand: YASKAWA Pages: 20

Brand: YASKAWA Pages: 17

Brand: YASKAWA Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands