Husqvarna F2101 Repair Manual Download Page 62

Page: 62 / 310

9 SHOCK ABSORBER, SWINGARM

9.12

Mount screw

but do not tighten yet.

Guideline

Screw, bottom

M10

shock absorber

•

Info

60 Nm (44.3 lbf ft)

Loctite

2701

Raise the wheel slightly to be able to mount the screw

more easily.

Position the linkage lever.

Mount and tighten fitting @.

Guideline

Nut, linkage lever to

M 14x1 .5

angle lever

Info

80 Nm (59 lbf ft)

Raise the wheel slightly to be able to mount the screw

more easily.

- Tighten screw

Guideline

Screw, bottom

M10

shock absorber

- Tighten fitting

CD.

Guideline

Nut, linkage lever on

M 14x1 .5

swingarm

60 Nm (44.3 lbf ft)

Loctite

2701

80 Nm (59 lbf ft)

•

Servicing the shock absorber

Caution

Risk of injury

rectly.

Parts of the shock absorber will fly off if the shock absorber is disassembled incor-

The shock absorber is filled with highly compressed nitrogen.

Please follow the description provided.

Condition

The shock absorber has been removed.

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands