Husqvarna F2101 Repair Manual Download Page 15 | Manualshive

Page: 15 / 310

background image

402001-10

400733-01

5 MOTORCYCLE

Remove the plug-in stand

0-

Shift the transmission to idle.

Condition

Ambient temperature: < 20 °C (< 68 °F)

Push the cold start button in all the way.
Press the electric starter button CD.

Info

Press the electric starter button for at most 5 sec

onds. Wait for 30 seconds before a further attempt
at starting.
At temperatures below 15 °C (60 °F), several
attempts at starting may be necessary to warm-up
the lithium-ion battery and thereby increase the
starting power.

During the starting process, the malfunction indi

cator lamp lights up.

5.4

Startin the motorcycle to check the function

Danger

Danger of poisoning

Exhaust gases are toxic and inhaling them may result in unconsciousness and

death.

Always make sure there is sufficient ventilation when running the engine.

Use an effective exhaust extraction system when starting or running the engine in an enclosed

space.

400733-01

Shift the transmission to idle.

Press the electric starter button CD.

Info

Press the electric starter button for at most 5 seconds.

Wait for 30 seconds before a further attempt at start
ing.
At temperatures below 15 °C (60 °F), several attempts
at starting may be necessary to warm-up the lithium
ion battery and thereby increase the starting power.

During the starting process, the malfunction indicator

lamp lights up.

Do not open the throttle.

13

«
...
13
14
15
16
17
...
»

Summary of Contents for F2101























































































































































































































































































































Reviews:

No comments

Related manuals for F2101

Speedglas G5-02

Brand: 3M Pages: 17

Speedglas 9100 MP

Brand: 3M Pages: 72

Brand: 3M Pages: 84

Brand: Cake Pages: 13

Brand: Yamaha Pages: 860

Brand: Qingqi Pages: 48

Power Commander III 718-411

Brand: Dynojet Pages: 3

Brand: R&G Pages: 21

Brand: OKBABY Pages: 35

Battery Relocation Kit

Brand: BoxerCafe Pages: 7

Brand: Malaguti Pages: 242

GM STAR 250 1986

Brand: Maico Pages: 32

Brand: DYNATEK Pages: 4

Brand: DYNATEK Pages: 5

Brand: SW-Motech Pages: 2

HPS.11.258.900-01

Brand: SW-Motech Pages: 2

TRT.00.787.32500/B

Brand: SW-Motech Pages: 6

Brand: Tractel Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands