Husqvarna F2101 Repair Manual Download Page 18

Page: 18 / 310

6 FORK, TRIPLE CLAMP

6.5

Removing the fork legs

6.6

lnstallin the fork le s

402556-10

Remove the motorcycle from the lift stand. (

�

p. 12)

Preparatory work

Raise the motorcycle with a lift stand. (

�

p. 12)

Remove the front wheel. (

�

p. 112)

Main work

Remove screws

and take off the clamp.

Remove screws

and take off the brake caliper.

- Allow the brake caliper and brake line to hang tension-free to

the side.

Info

Do not pull the hand brake lever when the front wheel

is removed.

Loosen screws (D. Take out the left fork leg.

Unscrew screws

Take out the right fork leg.

Main work

Position the fork legs.

✓ Bleeder screws

are positioned toward the front.

Info

The rebound damping is located in right fork leg REB

(red adjusting screw). The compression damping is

located in left fork leg

COMP

(white adjusting screw).

Grooves are milled into the side of the upper end of
the fork legs. The second milled groove (from the top)
must be flush with the top edge of the upper triple

clamp.

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands