Husqvarna F2101 Repair Manual Download Page 197

Page: 197 / 310

17.4.18 camshafts, checking

311564-10

17 ENGINE

Check the camshafts for damage and wear.

If there is damage or wear:

Change the camshafts.

If the surface of the cams is damaged, check the oil

supply to the camshaft and cam lever.

17.4.19 Checking the pivot points of the camshafts

310430-10

310431-10

310432-10

Check the pivot points of the camshafts.

If there is damage or wear:

Change the cylinder head with the camshaft bearing
bridge.

Position the camshafts.

✓ The valves are not activated.

Insert the

Plastigauge

clearance gauge in area

Plastigauge

clearance gauge (60029012000) (

p. 289)

Position camshaft bearing bridge

Mount and tighten the

screws.

Guideline

Screw,

M7x1

14 Nm (10.3 lbf ft)

camshaft

Lubricated with engine

bearing bridge

Info

Ensure that the dowel pins are seated properly.
Do not turn the camshaft.

oil

195

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands