manualshive.com logo in svg

Husqvarna F2101, Repair Manual

Share
Download
Husqvarna F2101 Repair Manual Download Page 192

17  ENGINE 

17.4.9 

190 

- Position special tool 

@) 

with the heel pointing down.

I  Crankshaft pressing tool insert (79029008000) (

� 

p. 293)

- Press in the upper crankweb as far as possible.

Info 

The press mandrel must be positioned over the crank 

pin. 

- Take the crankshaft out of the special tool and check that the

connecting rod can move freely.

- Measure axial play 

(9 

between the connecting rod and the

crankwebs using the special tool.
I  Feeler gauge (59029041100) (

� 

p. 288) 

Connecting rod - axial 

play of lower conrod bear­

ing 

0.20 ... 0.45 mm (0.0079 

... 0.0177 in) 

If the measured value is less than the specification: 

- Correct it so the dimension is equal to the specified

value.

Finishing work 

- Check the crankshaft run-out at the bearing pin. (

a 

p. 190)

Checking the crankshaft run-out at the bearing  pin 

- Position the crankshaft on a roller block.

- Turn the crankshaft slowly.

Check the crankshaft run-out on both bearing pins.

Crankshaft - run-out at 

bearing pin 

$ 0.03 mm ($ 0.0012 in) 

If the crankshaft run-out at the bearing pin is larger than 

the specification: 

- Align the crankshaft.

.. 

Summary of Contents for F2101























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands