Husqvarna F2101 Repair Manual Download Page 198

Page: 198 / 310

17 ENGINE

310433-10

17.4.20 valves, removing

310434-10

196

Remove camshaft bearing bridge

again. Compare the

Plastigauge

clearance gauge with the specifications on the

packaging.

Guideline

Camshaft bearing - sleeve bearing

Radial clearance

Wear limit

•

Info

0.020 ... 0.054 mm (0.00079

... 0.00213 in)

0.065 mm (0.00256 in)

The width of the

Plastigauge

clearance gauge is a

measure of the bearing play.

- Take off the camshafts and clean the parts.

Remove screw plugs

with the O-ring.

Screw appropriate screw

into the cam lever shaft.

Hold cam levers

and remove the cam lever shaft.

Info

If the cam levers will continue to be used, note down

their installation position.

- Take the shims from the valve spring retainers and put them

aside corresponding to their installation position.

Pre-tension the valve springs using the special tool.

Valve spring mounter (59029019000) (

I!;!

p. 288)

Insert for valve spring lever (79029060000) (

p. 294)

Insert for valve spring lever (77029041200) (

�

p. 291)

Remove the valve keys and release the tension on the valve

springs.

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands